What the 24-in-1 Swab Kit Includes

The VSGO V-S03E 24-in-1 Full-frame Sensor Cleaning Swabs pack contains 24 individually sealed, dry swabs designed specifically for full-frame camera sensors. Each swab has a 24 mm (0.94 in) wide head covered in a super fine microfiber cloth. The set does not include cleaning fluid, so you'll need to supply your own if you prefer wet cleaning.

Every swab is manufactured in a 100% dustless environment and vacuum-sealed to keep it clean until you open it. The swab head is made of micrometer-level fiber cloth that absorbs and sweeps away invisible particles without leaving streaks or blemishes.

Evidence from the VSGO Catalog

  • 24-in-1 Full-frame Sensor Cleaning Swabs V-S03E: The extremely soft and flexible swab head is completely covered by a super fine microfiber cloth. It helps you clean your sensor effectively and without leaving streaks or blemishes. (This set does not include camera cleaning fluid) Confirms the swabs are dry-use only unless you add fluid, and that the microfiber material is designed for streak-free cleaning.

    24-in-1 Full-frame Sensor Cleaning Swabs V-S03E

    24-in-1 Full-frame Sensor Cleaning Swabs V-S03E

  • 24-in-1 Full-frame Sensor Cleaning Swabs V-S03E: Sensor Cleaning Swab Size: 24mm (0.94in), Dry CCD CMOS Clean Swab. This full-frame sensor cleaning swab is compatible for all full-frame camera sensors. Verifies the swab width is correct for full-frame sensors and that compatibility covers all full-frame cameras.

  • 24-in-1 Full-frame Sensor Cleaning Swabs V-S03E: Super soft and flexible swab head spreads pressure evenly across the sensor and cause NO damage. Sensor cleaning swab grip matching the ergonomic, is comfortable to use. The soft head and ergonomic grip reduce the risk of scratching or uneven pressure during cleaning.

How to Clean a Full-frame Sensor with the 24-in-1 Swabs

Before you begin, make sure your camera battery is fully charged and you are working in a low-dust environment. The following steps are based on the swab design and general sensor cleaning best practices.

  1. Prepare the camera: Lock the mirror up (if using a DSLR) or enter sensor cleaning mode (mirrorless cameras). Remove the lens and set the camera on a stable surface with the sensor opening facing down to reduce dust entry.
  2. Blow off loose dust: Use a blower (not compressed air) to remove any loose particles from the sensor surface. This step reduces the risk of scratching when you wipe.
  3. Open a fresh swab: Tear open the vacuum-sealed package. Avoid touching the swab head. If you plan to use cleaning fluid, apply one or two drops to the swab head and let it wick in. The VSGO V-S03E swabs are dry by default but can be used with fluid.
  4. Wipe the sensor: Place the swab flat against the sensor surface. Gently drag it from one side to the other in a single, smooth motion. Do not scrub back and forth. Use a fresh swab for each pass if needed.
  5. Inspect the result: Reattach the lens or use a sensor loupe to check for remaining spots. Repeat with a new swab if necessary. The swab head is designed to spread pressure evenly and leave no streaks.

Compatibility and Usage Notes

The VSGO V-S03E swabs are compatible with all full-frame camera sensors. Their 24 mm width covers the sensor in one pass, reducing the need for multiple swipes. Because the swabs are dry, they work well for light dust removal. For oily or sticky spots, you may need to add a small amount of sensor cleaning fluid.

The swab head is soft and flexible, which helps it conform to the sensor surface without applying uneven pressure. The ergonomic grip makes it comfortable to hold and control during the cleaning motion.

What the Catalog Does Not Confirm

The supplied records do not include step-by-step cleaning instructions from VSGO. The steps above are based on the swab's design and general sensor cleaning best practices. Always consult your camera's manual for the correct sensor cleaning mode. The swabs are intended for single use; reusing a swab may reintroduce debris.