Start with the two tubes and what they are meant to do
The AeroTech 11924 is a 1.9-inch diameter, 22.75-inch long body tube pre-slotted for three fins and two thru-the-wall launch lugs. The AeroTech 12918 is a 29mm motor mount tube, 17.75 inches (451 mm) long with a 1.1mm wall. Both are the same tubes supplied with AeroTech rocket kits, so they are intended to work together in a kit-style build.
This guide covers the fit relationship between those two parts: how the motor mount sits inside the body tube, how the pre-cut slots affect assembly, and what to verify before you glue anything. It does not replace your kit instructions or a motor manufacturer’s compatibility chart.
Body tube dimensions that drive the fit
-
AeroTech 1.9 x 22.75 inch 3-Slot Body Tube - 11924: 1.9 inch diameter x 22.75 inch length; outer diameter 1.88 inches, inner diameter 1.8 inches, wall thickness 0.04 inches. The 1.8-inch inner diameter is the space your motor mount assembly must fit inside. Check your centering rings and internal components against this number before assembly.
AeroTech 1.9 x 22.75 inch 3-Slot Body Tube - 11924
-
AeroTech 1.9 x 22.75 inch 3-Slot Body Tube - 11924: Pre-slotted for 3 fins and 2 Thru-The-Wall launch lugs. The slots are already cut, so fin and lug placement is set by the tube. Slot alignment with the motor mount and fins becomes a dry-fit check rather than a layout task.
Motor mount tube dimensions to match
-
AeroTech 29mm x 17.75 inch Motor Mount Tube - 12918: 29mm x 17.75 inch (451 mm) motor tube with a 1.1mm thick wall. The 29mm size refers to the motor mount inside diameter, so it accepts 29mm motors. The 17.75-inch length sets how far the mount extends inside the 22.75-inch body tube.
AeroTech 29mm x 17.75 inch Motor Mount Tube - 12918
-
AeroTech 29mm x 17.75 inch Motor Mount Tube - 12918: The same motor mount tube supplied with AeroTech rocket kits. If you are replacing a tube from an AeroTech kit, this is the same part type, which reduces the chance of a dimensional mismatch.
Dry-fit sequence before any adhesive
The catalog does not supply a step-by-step assembly procedure, so treat these as fit checks based on the listed dimensions and features. Follow your kit’s instructions for the actual build.
- Check the motor mount outside diameter against the body tube inside diameter: The body tube inner diameter is 1.8 inches. Your motor mount assembly, including centering rings, must fit inside that space. Measure your parts rather than assuming.
- Slide the motor mount into the body tube and check length: The motor tube is 17.75 inches long and the body tube is 22.75 inches long. Confirm how far the mount should sit from each end according to your kit’s motor mount location.
- Align the fin slots with the motor mount: The body tube has three pre-cut fin slots. With the mount dry-fitted, check that the slot positions line up with the fin tabs or thru-the-wall fin roots you plan to use.
- Check the two thru-the-wall launch lug slots: The body tube is slotted for two thru-the-wall launch lugs. Confirm the lug positions clear the motor mount and any internal hardware.
- Confirm motor fit in the mount: The motor mount is 29mm. Test-fit a 29mm motor or motor adapter if you have one, following the motor manufacturer’s instructions. Do not force a motor that does not seat.
Where slot alignment actually matters
The 11924 body tube arrives with three fin slots and two launch lug slots already cut. That saves layout work, but it also means the slot pattern is fixed. During dry fit, the main question is whether your fin roots and launch lug mounts reach the motor mount tube the way the slot pattern expects.
If you are building from a kit that uses this tube, the slots should match the kit’s fin and lug locations. If you are using the tube in a scratch build, compare the slot spacing to your fin pattern before committing. The catalog does not list slot dimensions or angular spacing, so measure the tube you receive rather than relying on a drawing.
What the catalog confirms and what it leaves to your kit instructions
The supplied records give dimensions and slot counts, not a complete assembly manual. Use this table to separate what is known from what you must verify locally.
- Confirmed by the catalog: Body tube: 1.9-inch class, 22.75 inches long, 1.8-inch inner diameter, 0.04-inch wall, three fin slots, two thru-the-wall launch lug slots. Motor mount: 29mm, 17.75 inches (451 mm) long, 1.1mm wall.
- Not confirmed by the supplied information: Centering ring dimensions, motor mount position inside the body tube, adhesive type, slot angular spacing, and maximum motor impulse are not listed in the supplied records. Check your kit instructions or the motor manufacturer’s data for those.
A practical order of work
Build in a sequence that lets you correct fit problems before adhesive sets. Start by dry-fitting the motor mount and centering rings into the body tube without glue. Mark the motor mount position lightly, then remove it. Test-fit your fins and launch lugs in the pre-cut slots to confirm they reach the motor mount as intended.
Only after those checks should you move to bonding, following your kit’s instructions for adhesive and cure time. The catalog does not specify adhesives or cure schedules for these tubes, so do not substitute generic advice for the manufacturer’s procedure.
If you are replacing a damaged tube in an existing AeroTech kit, keep the original motor mount and fin positions as your reference. The 11924 and 12918 are the same tube types supplied with AeroTech kits, which makes them a sensible starting point for a repair, but always compare the actual part you receive to the one you are replacing.

