Understanding the Door Hinge Set

The Buster + Punch Door Hinge (set of 2) is a solid metal hinge designed to match the brand's door hardware. It measures 76 x 51 x 2 mm and comes in a brushed metal finish stamped with the B+P logo. The hinge is intended for standard residential doors and is sold in pairs. Available finishes include Smoked Bronze, Steel, Brass, and Welders Black, allowing you to coordinate with your existing hardware.

Key Product Details

  • DOOR HINGE / SET OF 2 / 76 X 51 X 2 MM: Solid metal construction with a brushed metal finish and B+P logo stamp. The solid build and branded finish ensure the hinge complements other Buster + Punch hardware and provides durable performance.

    DOOR HINGE / SET OF 2 / 76 X 51 X 2 MM

    DOOR HINGE / SET OF 2 / 76 X 51 X 2 MM

  • DOOR HINGE / SET OF 2 / 76 X 51 X 2 MM: Dimensions: 76 x 51 x 2 mm. Sold in pairs. This standard size fits most residential doors. The 2 mm thickness offers a sturdy feel without being bulky. Sold in pairs means you get both hinges needed for a typical door.

  • DOOR HINGE / SET OF 2 / 76 X 51 X 2 MM: Available finishes: Smoked Bronze, Steel, Brass, Welders Black. You can match the hinge finish to your door handles, locks, and other hardware for a cohesive look.

Step-by-Step Installation

Before you begin, ensure you have the correct hinge size and finish for your door. The supplied information confirms the hinge is suitable for residential doors with standard sizing for ease of fitting. No specific installation instructions are included in the product record, so the following steps are based on general practice for this type of hinge.

  1. 1. Prepare the Door and Frame: Mark the hinge positions on the door edge and the door frame. Standard placement should follow the product instructions. Use a sharp pencil and a square to ensure marks are level.
  2. 2. Chisel the Mortises: Use a chisel to cut shallow recesses (mortises) for the hinge leaves. The depth should match the hinge thickness (2 mm) so the hinge sits flush. Take care not to cut too deep.
  3. 3. Attach the Hinges to the Door: Position the hinge on the door mortise and secure it with the supplied screws. Ensure the hinge pin is oriented correctly (typically the pin faces the interior of the room). Tighten screws firmly but avoid over-tightening.
  4. 4. Attach the Hinges to the Frame: Hold the door in place and mark the screw holes on the frame. Remove the door, drill pilot holes, then reattach the door and secure the hinge leaves to the frame. Check that the door swings freely before fully tightening.
  5. 5. Final Alignment Check: Open and close the door several times. If it binds or gaps unevenly, adjust the hinge screws slightly. For minor adjustments, you can loosen the screws on the frame side and shift the door slightly before retightening.

Alignment Tips for Smooth Operation

Proper alignment ensures the door closes evenly and without strain on the hinges. After installation, check the gap between the door and frame: it should be consistent along the top and sides. If the door sags, the hinge screws may need tightening or the mortise may need slight deepening. Because the hinge is solid metal and 2 mm thick, it provides a stable base for adjustment. The supplied information does not specify exact gap tolerances, so use your judgment based on the door's fit.

Choosing the Right Finish

The hinge is available in Smoked Bronze, Steel, Brass, and Welders Black. Consider the finish of your existing door handles, locks, and other hardware. For a consistent look, choose the same finish as your Buster + Punch door hardware. If you are mixing finishes, ensure they complement each other (e.g., brushed brass with warm bronze tones). The hinge's brushed metal finish has a subtle sheen that works well in both modern and traditional settings.

What the Supplied Information Does Not Cover

The product record does not include specific installation instructions, torque specifications, or recommended screw types. For doors that are unusually heavy or non-standard, consult a professional installer. The hinge is designed for standard residential doors, but the exact weight capacity is not stated. If you have a solid-core or oversized door, verify compatibility with the manufacturer before installation.