Quick answer

Buy the Tormach TTS 10 mm holder if your mill uses the TTS quick-change system and your end mills have 10 mm Weldon shanks. Buy the 2MT 3/8 holder if your spindle has a 2 Morse taper and a 3/8-16 NC drawbar, and you run 3/8-inch shank tooling.

Spindle interface decides the holder, not the cutter size

The two holders mount differently: the Tormach TTS holder is a quick-change set-screw holder for the TTS system, while the 2MT holder has a Morse taper shank and uses a 3/8-16 NC drawbar. No adapter makes a 2MT holder fit a TTS spindle or the reverse. Check your spindle taper and drawbar thread before comparing prices or cutter sizes.

Shank style and holding method affect setup and rigidity

The TTS holder uses a set screw and is intended for end mills with a Weldon shank (a flat on the shank); it can also hold certain Silver & Deming style drill bits. The 2MT holder is an adapter for 3/8 shank end mills. If your cutters lack a Weldon flat, confirm the holder's clamping method will secure them safely—neither product is a collet, so round-shank tooling may not be ideal.

Quick change versus drawbar: workflow trade-off

A TTS quick-change holder speeds tool changes when you keep multiple holders set up for different cutters, but it only works within the TTS ecosystem. A 2MT holder with a drawbar is a simpler, lower-cost interface for a single mill, yet each tool change means threading and unthreading the drawbar. Choose based on how often you swap tools, not on the holder price alone.

Decision rules for choosing between TTS 10 mm and 2MT 3/8

  • Match the spindle taper: If your mill has a Tormach TTS spindle, choose the TTS 10 mm holder. If it has a 2 Morse taper spindle, choose the 2MT 3/8 holder. Do not attempt to adapt one to the other.
  • Confirm the drawbar thread: The 2MT holder requires a 3/8-16 NC drawbar. If your drawbar has a different thread, this holder will not pull in correctly—check the thread before buying.
  • Check cutter shank size and style: Use the TTS 10 mm holder with 10 mm Weldon-shank end mills (or certain Silver & Deming drill bits). Use the 2MT 3/8 holder with 3/8-inch shank end mills. If your cutters are a different size, neither holder is a direct fit.
  • Weigh tool-change frequency: Choose TTS if you want quick changes across multiple pre-set holders. Choose 2MT if you prefer a conventional drawbar setup and change tools less often.

Product facts

  • End Mill Holder, Tormach TTS, 10 mm: Quick-change Tormach TTS set-screw holder for 10 mm end mills and other milling tools with a Weldon shank. It suits TTS-equipped mills where fast cutter changes and 10 mm Weldon-shank tooling are the priority.

    End Mill Holder, Tormach TTS, 10 mm

    End Mill Holder, Tormach TTS, 10 mm

  • End Mill Holder, 2MT, 3/8 CLEARANCE: 2 Morse taper shank holder for 3/8 shank end mills, using a 3/8-16 NC drawbar. It fits 2MT spindles with that drawbar thread, so verify both before ordering.

    End Mill Holder, 2MT, 3/8 CLEARANCE

    End Mill Holder, 2MT, 3/8 CLEARANCE

Who should buy which holder

Best for

  • Machinists with a Tormach TTS spindle who use 10 mm Weldon-shank end mills and want quick tool changes
  • Operators with a 2 Morse taper spindle and 3/8-16 NC drawbar who run 3/8-inch shank end mills

Not for

  • Mills with an R8 spindle—neither holder fits an R8 taper
  • Cutters whose shank size or style does not match the holder (for example, 3/8-inch shanks in the TTS 10 mm holder)
  • Anyone unsure of their spindle taper or drawbar thread—verify first