Quick answer

The Foodcube Auto Water Filler connects directly to your existing water source and automatically maintains consistent moisture in your Foodcube system, eliminating daily watering. For best results, install it on a level surface near your Foodcube, use the included fittings to connect to a standard garden hose or tap, and check for leaks before turning on the water. It is designed for easy installation and fits standard garden setups.

What you need before you start

Before beginning, gather the Foodcube Auto Water Filler, a standard garden hose or direct tap connection, and a clean cloth for wiping connections. Ensure your Foodcube system is assembled and positioned where you want it. The Auto Water Filler is designed to connect directly to existing water sources, so no special tools are required for basic setup.

Step 1: Position the Auto Water Filler

Place the Auto Water Filler on a flat, stable surface near your Foodcube system. It should be close enough that the water line can reach the Foodcube without straining, but not so close that it interferes with plant growth. Avoid placing it in a low spot where water might pool.

Step 2: Connect to your water source

Attach the Auto Water Filler to your garden hose or directly to a tap using the provided fittings. Hand-tighten connections to avoid cross-threading. If using a hose, ensure it is not kinked and that the washer is in place to prevent leaks.

Step 3: Connect to the Foodcube system

Run the outlet line from the Auto Water Filler to your Foodcube reservoir. The connection should be secure but not over-tightened. The Auto Water Filler automatically supplies water to maintain consistent moisture levels, so the line must be free of obstructions.

Step 4: Turn on the water and check for leaks

Slowly open the water supply. Listen for hissing or dripping sounds and check all connections for leaks. If you find a leak, turn off the water, tighten the connection, and try again. A small drip can waste water and reduce efficiency.

Step 5: Test the automatic filling

Allow the system to run for a few minutes. The Auto Water Filler should begin supplying water to the Foodcube. Check that the water level in the reservoir rises to the desired level and that the flow stops when full. If it does not stop, check for blockages or incorrect installation.

Step 6: Adjust and monitor

After the initial test, monitor the system over the next few days. Adjust the water supply if needed—some setups may require a lower flow rate to prevent overflow. The goal is consistent moisture without waterlogging. Once set, the system requires minimal attention.

Setup steps with checkpoints

  1. Position the unit: Place the Auto Water Filler on a level surface near your Foodcube, ensuring the water line can reach without tension. Checkpoint: The unit should not wobble or sit in a depression where water could pool.
  2. Connect to water source: Attach the inlet to your garden hose or tap using the provided fittings. Hand-tighten only. Common mistake: Over-tightening can crack plastic fittings; stop when snug.
  3. Connect to Foodcube: Run the outlet line to the Foodcube reservoir and secure the connection. Checkpoint: The line should be free of kinks and obstructions.
  4. Turn on water and check for leaks: Slowly open the water supply and inspect all connections for drips. Common mistake: Forgetting to check the washer in the hose connector; a missing washer causes leaks.
  5. Test automatic filling: Let the system run and confirm that water flows into the Foodcube and stops when full. Checkpoint: If water does not stop, check for blockages or incorrect float valve installation.
  6. Adjust and monitor: Observe the system over a few days and adjust the flow rate if needed to prevent overflow. Next step: Once stable, you can rely on the system for hands-free watering.

Product facts

  • Foodcube™ Auto Water Filler: The Foodcube Auto Water Filler from Vego Garden provides a reliable, hands-free way to keep your garden hydrated, turning a garden into a low-maintenance oasis. This means you can spend less time watering and more time enjoying your garden, especially during busy weeks.
  • Foodcube™ Auto Water Filler: Automatically supplies water to your Foodcube system, maintaining consistent moisture levels without daily attention. Consistent moisture helps prevent plant stress and improves growth, even if you forget to water.
  • Foodcube™ Auto Water Filler: Designed for easy installation; fits standard garden setups and connects directly to existing water sources. No special plumbing or tools are needed, so you can set it up quickly with a standard hose or tap.
  • EZCube Self-Watering Planter 21" x 24" & EZCube Mesh Cover System Bundle: EZCube Self-Watering Planter 21" x 24" & EZCube Mesh Cover System Bundle takes out the guesswork with a compact, self-watering system that’s easy to set up, easy to care for, and built to grow real results in tight spaces. If you have a small space, this bundle pairs well with the Auto Water Filler for a complete low-maintenance setup.