Start with the fin set, not the glue

The FS-Onyx fin set from LOC Precision is built for a 3.10-inch airframe, and its fin tabs are sized to reach a 29mm motor tube. That single fact should shape your entire build order: before you bond anything, confirm that your airframe diameter and motor mount match the fin set’s geometry. If they do, the tabs help you achieve secure installation and reliable fin alignment. If they don’t, no amount of epoxy will fix the mismatch.

This guide walks through the fit checks that matter for a fiberglass rocket assembly using the FS-Onyx. It focuses on what the supplied product evidence supports—three 1/8-inch-thick fins, a complete set, and tab reach to a 29mm motor tube—and flags where you need to verify dimensions yourself.

What the FS-Onyx fin set gives you

  • FS-Onyx: Fits LOC 3.10-inch diameter airframes. Confirm your airframe’s outside diameter before ordering; a 3.10-inch tube is the baseline for every downstream fit check.

    FS-Onyx

    FS-Onyx

  • FS-Onyx: Includes three fins, each 1/8-inch thick. Three fins form a complete set; the 1/8-inch thickness is your reference for slot width and fin alignment fixture spacing.

  • FS-Onyx: Fin tabs are sized to reach a 29mm motor tube. Tab reach determines whether your motor mount sits at the correct depth for secure installation; check this before any bonding.

Fit checks to run before you mix epoxy

  1. Measure your airframe diameter: The FS-Onyx is designed for a 3.10-inch airframe. Measure your tube’s outside diameter and compare. If it differs, the fin set is not a direct fit and you should not proceed without confirming compatibility.
  2. Dry-fit the motor tube and fin tabs: Slide your 29mm motor tube into the airframe and test whether the fin tabs reach it. The tabs should contact the motor tube without forcing. If they fall short or interfere, stop and identify whether the motor tube diameter or mounting depth is off.
  3. Check fin slot width against 1/8-inch fin stock: Each fin is 1/8-inch thick. If your airframe already has slots, verify they accept that thickness without excessive play. If you are cutting slots, use a 1/8-inch reference and test with a scrap piece before committing.
  4. Trial-fit all three fins: Insert each fin dry and check that the set sits at the same depth. Because the package includes three fins, you can rotate them to find the best alignment before any adhesive is applied.
  5. Plan fin alignment before bonding: The FS-Onyx is intended for reliable fin alignment, but the set does not include alignment fixtures. Use your preferred method—such as a guide or jig—to hold fins perpendicular and evenly spaced while the adhesive cures.

Where the 29mm motor tube changes your build

The fin tabs are sized to reach a 29mm motor tube, so your motor mount is not just a power choice—it is a structural reference. If you plan to use a different motor tube diameter, the tabs may no longer reach, and you would need to modify the mount or choose a different fin set. The supplied information does not confirm compatibility with motor tubes other than 29mm, so treat any change as a custom modification rather than a drop-in swap.

This also affects your internal fillet strategy. Because the tabs reach the motor tube, you can create fillets at the tab-to-tube joint for secure installation. The exact adhesive and fillet size are not specified in the supplied information; follow your kit’s instructions or your own proven high-power build practices.

Fiberglass assembly tips that apply to this fin set

The FS-Onyx fins are described as balancing strength and weight at 1/8-inch thickness. For a fiberglass rocket assembly, that means you should prepare bonding surfaces according to your airframe manufacturer’s guidance—typically by cleaning and lightly abrading mating areas—but the supplied product record does not include surface-preparation steps. Use the airframe and adhesive instructions you already trust.

Keep the fin set’s geometry in mind when planning your build sequence. Because the tabs are designed to reach a 29mm motor tube, it is easier to verify fit before the motor mount is permanently installed. If you bond the motor mount first, you lose the ability to adjust depth if the tabs do not align as expected.

Product facts that affect your decision

  • FS-Onyx: Suitable for high-power rocketry projects requiring reliable fin alignment. This fin set is intended for high-power use, so your build should include appropriate reinforcement and alignment checks—not just a sport-kit assembly.
  • FS-Onyx: The FS-Onyx fin set from LOC Precision is designed for builders working with a 3.10-inch airframe. If your project uses a different airframe diameter, this set is not the right starting point; confirm your tube size before ordering.