Quick answer

Build the Highland Torsos x5 as the core of a Scottish guard: clean and test-fit each resin torso before adding kilted legs, then paint the tartan in thin horizontal and vertical bands rather than trying to freehand a full pattern in one pass.

Why the torso is the right starting point for a Highland regiment

Starting a Highland regiment from torsos rather than full miniatures gives you control over the parts that define the unit: the kilt, the sporran, the bonnet and the weapon arms. The trade-off is that you must source or sculpt those lower-body and accessory parts yourself, so plan the whole figure before you glue anything.

The Highland Torsos x5 set is cast in resin at 28mm heroic scale, which means the proportions match heroic-scale arms and legs rather than true-scale historical figures. Test any legs or arms you intend to use against a torso before committing to a batch, because a small shoulder or waist mismatch becomes obvious across five figures.

Tartan is a discipline of thin layers, not a single pattern

A convincing 28mm tartan comes from a few translucent bands crossing at right angles, not from painting every historical stripe. Choose two base colours and one accent, keep the bands narrow, and let the base colour show through. If you try to reproduce a full clan sett at this scale, the pattern turns into mud and the kilt loses its shape.

Paint the tartan before you attach arms that cross the body, and before you glue the figure to a finished base. Reaching the sides and rear of a kilt around a rifle or a pack is the most common reason a tartan scheme looks unfinished.

Step-by-step: assemble and paint the Highland Torsos

  1. Wash and inspect the resin: Scrub the five torsos in warm water with a drop of dish soap, rinse, and let them dry fully. Check each torso for mould lines and thin flash around the neck, shoulders and waist. Common mistake: priming straight out of the pack, which traps release agent and causes paint to bead. Mark any torso with a visible bubble or short cast at the waist and set it aside for a conversion that hides the flaw.
  2. Test-fit legs and arms before gluing: Dry-fit your chosen kilted legs and arms to each torso. Trim the contact points with a sharp blade rather than forcing the joint, and keep the waist join tight. Checkpoint: the shoulder line should sit level across all five figures so the unit looks like one regiment. Number the torsos and their matched parts on the inside of the waist so you do not mix up fitted pairs later.
  3. Build the kilt silhouette: Attach the legs and add a simple sporran block at the front of the waist. If you are sculpting a kilt, keep the pleats shallow and vertical at the rear and reserve the flat front apron for the tartan. Common mistake: over-sculpting deep pleats that read as folds of cloth rather than a kilt. Photograph the bare figure from the side; if the kilt line is unclear in grey resin, it will be unclear in paint.
  4. Prime and block in the base colours: Prime in a light grey or white so the tartan colours stay bright. Block in the kilt base colour, then the skin, hose and jacket. Keep the kilt area clean and free of thick paint. Checkpoint: two thin coats of base colour, not one heavy coat that fills the pleat detail. Leave the kilt base to dry fully before starting bands; wet paint smears the first stripe.
  5. Lay the tartan bands: Paint narrow horizontal bands of your accent colour across the kilt at even spacing, then cross them with vertical bands of the same colour. Thin the paint to a glaze so the base colour still reads through. Common mistake: making the bands too wide, which turns the sett into a checkerboard. Step back to arm's length after every two bands; if the pattern reads as a grid from that distance, it is wide enough.
  6. Add the thin cross-stripes: With a fine brush, add one or two very thin stripes in a third colour where the wide bands cross. Keep them broken and slightly uneven rather than perfectly straight. Checkpoint: the thin stripes should be visible but not dominate the kilt. If a stripe looks too strong, glaze the base colour thinly over it rather than repainting the whole kilt.
  7. Finish the figure and seal: Paint the bonnet, hose, sporran and metal parts, then apply a matte varnish to the whole figure. Varnish the kilt last so the tartan does not pick up dust while you handle the arms. Common mistake: handling the kilt with bare fingers during basing, which polishes the matte finish. Seal before adding any static grass or tufts so the flock does not stick to the kilt.

Product facts

  • Highland Torsos x5: Five Highland-themed torsos cast in durable resin at 28mm heroic scale. Five matching torsos let you build a consistent command group or squad while keeping the same shoulder and waist proportions for arm and leg swaps.

    Highland Torsos x5

    Highland Torsos x5