What the Kevlar Cord Does in Your Rocket

The AeroTech Kevlar Cord 24" Yellow (Q50053) is a 24-inch length of yellow Kevlar designed for use in model rocketry and related hobby applications. It provides a reliable tethering or recovery solution for your projects. In a typical rocket, this cord serves as the shock cord that connects the nose cone to the body tube after ejection, preventing the two parts from separating and ensuring a safe recovery.

Product Facts for the AeroTech Kevlar Cord 24" Yellow

  • Kevlar Cord 24" Yellow - Q50053: This 24-inch Kevlar cord in yellow is designed for use in model rocketry and related hobby applications. It provides a reliable tethering or recovery solution for your projects. Confirms the cord's intended role as a shock cord or tether, which is exactly what you need for attaching the nose cone to the body tube after launch.

    Kevlar Cord 24" Yellow - Q50053

    Kevlar Cord 24" Yellow - Q50053

  • Kevlar Cord 24" Yellow - Q50053: Length: 24 inches, Color: Yellow, Material: Kevlar The 24-inch length is suitable for many mid-power rockets; Kevlar provides high strength and heat resistance compared to elastic cords, though it does not stretch like rubber.

Step-by-Step Installation Guide

Follow these steps to install the Kevlar cord as a shock cord in your rocket. The supplied information does not include specific instructions from the manufacturer, so the procedure below follows standard hobby rocketry practice. Always check your rocket kit's manual for any specific guidance.

  1. 1. Prepare the cord and your workspace: Cut the cord to your desired length if needed; the supplied cord is 24 inches long. Have a lighter or hot knife on hand to seal the ends if the cord frays. Gather your rocket body tube, nose cone, and any attachment hardware such as a screw eye or loop.
  2. 2. Attach the cord to the nose cone: Tie a secure knot (e.g., a double overhand or figure-eight knot) around the nose cone's attachment point, such as a screw eye or a small loop. Ensure the knot is tight and will not slip under load. Leave a small tail for added security.
  3. 3. Attach the cord to the body tube: Thread the free end of the cord through the body tube's shock cord mount or around a sturdy internal structure (e.g., a motor mount tube). Tie another secure knot. For rockets without a dedicated mount, you can tie the cord around a dowel or a piece of stiff wire inserted through the tube wall, but this is less common.
  4. 4. Check the fit and length: The 24-inch cord should be long enough to allow the nose cone to separate fully from the body tube without putting stress on the attachment points. Avoid making the cord too short, which could cause the nose cone to snap back, or too long, which might tangle. Adjust the knot position if needed.
  5. 5. Test the assembly: Before flight, gently pull the nose cone away from the body tube to confirm the cord holds securely and the knots do not slip. Ensure the cord does not interfere with the parachute or streamer deployment. If using a Quest Q-jet motor, verify that the recovery wadding and parachute fit properly with the cord in place.

Tips for a Reliable Installation

Kevlar is strong but does not stretch like elastic shock cords. This means the cord will not absorb shock as well as a rubber cord, so ensure your attachment points are robust. The cord's heat resistance makes it ideal for use near motor ejection charges. If your rocket uses a parachute, attach the parachute to the cord using a small swivel or a separate loop to prevent tangling. The supplied information does not include specific care instructions, so handle the cord with care to avoid fraying.

Compatibility and Limitations

The AeroTech Kevlar Cord 24" Yellow is designed for model rocketry and related hobby applications. It is suitable for use with Quest Q-jet motors and many mid-power rockets. The supplied information does not specify a maximum weight or thrust rating, so use your judgment based on the rocket's size and expected forces. For heavy or high-power rockets, consider a longer or thicker Kevlar cord. The cord is not elastic, so it will not provide the same shock absorption as a rubber shock cord; plan your recovery system accordingly.