What You Need Before Starting

The AeroTech L2500ST-PS is a Plugged/Smoke reload for the RMS-98/5120 motor system. It uses Super Thunder propellant, which produces a bright violet-blue flame with minimal exhaust smoke. Because this is a plugged reload (no ejection charge), you will need a timer, altimeter, or radio-activated recovery system to deploy the parachute.

Before assembly, make sure you have the following:

AeroTech RMS-98/5120 motor hardware (available separately as a complete set or as individual parts).

A stainless steel forward seal disc (98FSDSS) – the reload requires this specific disc during assembly.

Proof of Level 2 High-Power certification (NAR or Tripoli) and proof of age (18+). This motor cannot be shipped without them.

HAZMAT shipping via UPS or FedEx is required for delivery.

Assembly Steps for the L2500ST-PS Reload

These steps are based on the supplied components and safety requirements. Always follow the manufacturer's instructions included with your hardware and reload kit.

  1. 1. Prepare the hardware: Ensure you have the RMS-98/5120 motor hardware assembled and clean. The reload kit includes all internal motor components and FirstFire Initiators, but the aluminum casing and closures come from the separate hardware set.
  2. 2. Install the forward seal disc: Place the stainless steel forward seal disc (98FSDSS) into the forward end of the motor casing. This disc is required for this reload and must be installed correctly to seal the propellant grain.
  3. 3. Insert the propellant grain: Slide the Super Thunder propellant grain into the casing, following the orientation marked on the grain. The reload kit contains one propellant grain weighing 2160 grams.
  4. 4. Add the aft closure and initiator: Install the aft closure from your hardware set. The reload kit includes FirstFire Initiators – insert one into the nozzle according to the initiator instructions. Do not use motor-actuated ejection components since this is a plugged reload.
  5. 5. Final checks: Verify that all O-rings and seals are properly seated. The motor diameter is 3.875 inches (98mm) and the casing length is 17.48 inches (444mm). Total motor weight is 5091 grams.

Key Specifications and Compatibility

  • AeroTech L2500ST-PS RMS-98/5120 Reload Kit (1 Pack) - 12250P: Total Impulse: 4680 N-sec; Average Thrust: 2500 newtons; Peak Thrust: 3114 N-sec; Thrust Duration: 1.8 seconds. These values help you choose an appropriate rocket and recovery system. The high average thrust is suited for heavy rockets, but the short burn time requires a fast liftoff.

    AeroTech L2500ST-PS RMS-98/5120 Reload Kit (1 Pack) - 12250P

    AeroTech L2500ST-PS RMS-98/5120 Reload Kit (1 Pack) - 12250P

  • AeroTech L2500ST-PS RMS-98/5120 Reload Kit (1 Pack) - 12250P: This motor requires installing a stainless steel forward seal disc (98FSDSS) during assembly. Using the correct seal disc is critical for safe operation. Do not substitute with another disc.

  • AeroTech L2500ST-PS RMS-98/5120 Reload Kit (1 Pack) - 12250P: High Power RMS reload kits are not compatible with Mid Power RMS products. This reload only fits RMS-98/5120 hardware. Attempting to use it with smaller hardware will cause failure.

The L2500ST-PS is a high-power motor requiring Level 2 certification through NAR or Tripoli. Federal law prohibits sale to persons under 18. You must provide proof of age and certification before shipment.

This motor is certified by TRA, NAR, and CAR. For international orders, State Department Licensing (SDL) is required for export.

Because the reload is plugged, you must use an electronic recovery system (timer, altimeter, or radio activation). Do not rely on motor delay or ejection charge.

AeroTech/Quest does not list recommended maximum liftoff weights for high-power motors. Use simulation software like RockSim or OpenRocket to determine safe liftoff weight for your rocket.