What You Need to Know Before Installing
The ARMORDILLO® CoveRex TFX Low Profile Tri‑Fold Hard Folding Tonneau Cover is designed specifically for the 2014–2018 GMC Sierra 1500 with a 5'8" bed. Before you start, confirm your truck matches this fitment — the cover is not universal and will not align correctly on other bed lengths or model years.
The clamp-on system requires no drilling or permanent modifications, making it a straightforward DIY project. The supplied information confirms that installation is designed to be simple, but it does not include detailed step-by-step instructions. The following guidance is based on the cover's known features and typical clamp-on tonneau installation practices.
CoveRex TFX Fitment and Key Features
-
ARMORDILLO® CoveRex TFX 2014-2018 GMC Sierra 1500 5'8" Bed Low Profile Tri-Fold Hard Folding Tonneau Cover: For 2014-2018 GMC Sierra 1500 5.8ft Truck Bed Ensures the cover sits flush along the bed rails for a factory‑level appearance and proper seal performance.
ARMORDILLO® CoveRex TFX 2014-2018 GMC Sierra 1500 5'8" Bed Low Profile Tri-Fold Hard Folding Tonneau Cover
-
ARMORDILLO® CoveRex TFX 2014-2018 GMC Sierra 1500 5'8" Bed Low Profile Tri-Fold Hard Folding Tonneau Cover: Clamp‑on, no‑drill installation You can install the cover without drilling holes or making permanent changes to your truck bed, preserving resale value and simplifying the process.
-
ARMORDILLO® CoveRex TFX 2014-2018 GMC Sierra 1500 5'8" Bed Low Profile Tri-Fold Hard Folding Tonneau Cover: Integrated perimeter seals help keep out most rain, snow, dirt, and debris Proper seal alignment during installation is critical to achieving the advertised weather protection.
Installation Steps for the CoveRex TFX on a 2014-2018 GMC Sierra 1500
The following steps are based on the cover's no-drill clamp system and tri-fold design. Always refer to the manufacturer's included instructions for torque specs and final adjustments.
- 1. Prepare the truck bed: Clean the bed rails thoroughly to remove dirt, wax, or debris. A clean surface helps the seals and clamps grip properly. Remove any existing bed accessories that might interfere with the cover's rail clamps.
- 2. Position the side rails: Place the left and right side rails along the bed rails. The CoveRex TFX uses a vehicle‑specific design, so the rails should align with the bed's contour without forcing. Do not tighten clamps yet — leave them loose enough to allow adjustment.
- 3. Attach the cover panels to the rails: With the cover in the folded (closed) position, set it onto the side rails. The tri-fold design allows you to rest all three panels on the rails at once. Adjust the cover so it sits centered and flush with the front of the bed.
- 4. Secure the clamps: Tighten each clamp evenly using the supplied hardware. The clamp-on system requires no drilling. Tighten just enough to hold the cover firmly — overtightening could damage the bed rail or clamp. Check that the cover does not shift when you push on it.
- 5. Test the fold and seal: Fold the cover open and closed several times. The built-in buckle and strap system keeps panels stable when driving with the cover partially open. Verify that the perimeter seals contact the bed rails evenly along all sides. If you see gaps, loosen the clamps and adjust the rail position slightly.
- 6. Final check with tailgate: Close the tailgate and ensure the cover's rear edge sits flush against it. When paired with a locked tailgate, the rigid panels create a secure storage space. Open and close the tailgate to confirm there is no interference.
What the Supplied Information Does Not Cover
The available evidence confirms that the CoveRex TFX uses a clamp-on system and is designed for simple DIY installation, but it does not include detailed torque values, specific clamp positioning diagrams, or instructions for bed liners. If your truck has a spray-in or drop-in bed liner, you may need to adjust clamp placement or trim liner material near the rail clamps — this is not covered by the supplied facts.
For best results, use the included hardware and follow any printed instructions that ship with the cover. If you are unsure about clamp placement or seal alignment, consult a professional installer to avoid damaging the cover or your truck bed.
