Confirm the machine before you touch the control box
The USB port in this guide is a specific replacement part, not a universal adapter. The catalog lists it for the DRO readers on deluxe HiTorque large bench mills, SIEG SX3.5L large bench mills with DRO, and deluxe HiTorque bench lathes (SIEG SC4). If your machine is a different model, or your DRO setup is not one of these, do not assume this port will fit.
The part is a USB 2.0 port. One end has a standard USB terminal that attaches to the USB power supply. The other end has a dual USB terminal that is available externally on the back of the control box. That dual terminal is the part you see and use from outside the machine.
What the catalog confirms about this port
-
USB Port, HiTorque Large Bench Mills and Lathes with DRO: USB 2.0 port for the DRO readers on deluxe HiTorque large bench mills and SIEG SX3.5L large bench mills with DRO and deluxe HiTorque bench lathes (SIEG SC4). This is the compatibility statement. Match your machine and DRO reader setup to this list before ordering.
USB Port, HiTorque Large Bench Mills and Lathes with DRO
-
USB Port, HiTorque Large Bench Mills and Lathes with DRO: One end of the part has a standard USB terminal to attach to the USB power supply while the other end has a dual USB terminal which is available externally on the back of the control box. It tells you the two connection points: power supply inside, dual terminal at the control box exterior.
-
USB Port, HiTorque Large Bench Mills and Lathes with DRO: The length of the cable between terminal ends is approximately 46". Use this to judge whether the run from the power supply to the control box back is practical on your machine.
A supported installation sequence
The catalog gives the connection logic and the mounting hardware for the dual terminal. It does not give torque values, a full teardown procedure, or a wiring diagram, so keep the work to what is described and stop if your machine differs.
- Power down and access the control box: The dual terminal mounts on the back of the control box. The catalog does not describe how to open or remove the control box, so follow your machine's own service information for access.
- Attach the standard USB terminal to the USB power supply: One end of the part is the standard USB terminal intended for the USB power supply. Make that connection before routing the cable.
- Route the cable to the back of the control box: The cable between terminal ends is approximately 46". Plan the route so the dual terminal reaches its external position without strain.
- Mount the dual terminal with two M3x10 screws: The dual terminal is mounted with two M3x10 screws. Those screws are not included, so have them on hand before you start.
- Confirm the external connection point: The dual terminal should be available externally on the back of the control box. The catalog does not specify a torque or a final test procedure, so verify the fit and the connection rather than guessing at settings.
Checkpoints before you order
- Machine model and DRO reader: The port is listed for deluxe HiTorque large bench mills, SIEG SX3.5L large bench mills with DRO, and deluxe HiTorque bench lathes (SIEG SC4). Confirm both the machine and the DRO reader setup.
- M3x10 screws: Two are required for the dual terminal and are not included. Source them before installation.
- Cable run: The terminal-to-terminal length is approximately 46". Check that this reaches from the USB power supply to the back of the control box on your machine.
- USB standard: The port is USB 2.0. The catalog does not state compatibility with other USB standards, so do not assume it.
Where the catalog stops
The supplied information does not include a wiring diagram, a control box removal procedure, torque values, or a step-by-step test routine. It also does not confirm interoperability with devices or standards beyond the listed machines and the USB 2.0 description. If your machine is not on the compatibility list, or you need those missing details, get them from the machine's service documentation before proceeding.
The part is priced at USD 6.77 in the catalog, with a comparison price of USD 9.95. That makes it a low-cost replacement, but the fit decision still rests on the model list and the two-terminal layout described above.
