What to Expect from JL Rear Fender Flares
Upgrading the rear fender flares on your 2018-2026 Jeep Wrangler JL is a straightforward way to improve clearance and update the look. The Body Armor 4x4 rear flare set is built from 3/16" steel plate and uses a high-clearance flat design that gives your Jeep a more aggressive stance while still providing 5-3/4" of coverage to help keep mud and debris off the body.
Before you start, it helps to understand what you're working with. These are rear flares only—they replace the stock units on the back of your JL. The two-stage powder coat light texture finish in black means they arrive ready to install, with no need for painting or additional coating.
Installation Steps for JL Rear Fender Flares
The exact steps can vary depending on your Jeep's trim and existing equipment, but the general process for replacing rear flares is consistent. Work on one side at a time, and have a helper available for aligning the new flares.
- Remove the stock rear flare: Start by removing the factory rear fender flare. On the JL Wrangler, this typically involves removing a few bolts or screws along the inner edge and gently prying the flare away from the body. Disconnect any wiring if your Jeep has fender-mounted lights.
- Clean the mounting area: Once the old flare is off, clean the exposed body panel and the mounting surface. Remove any dirt, old adhesive, or debris so the new flare sits flush.
- Position the new flare: Hold the Body Armor 4x4 rear flare up to the mounting location. The high-clearance flat design should align with the body lines. Check the fit before tightening anything.
- Secure the flare: Using the supplied hardware, attach the flare to the factory mounting points. Tighten the fasteners evenly, but don't over-torque—steel flares are heavy, but you want to avoid distorting the metal.
- Repeat on the other side: Follow the same process for the opposite rear flare. After both are installed, walk around the Jeep and check that the flares are evenly spaced and securely fastened.
Tips for a Clean Install
Because the Body Armor 4x4 rear flares are made from 3/16" steel, they add noticeable weight compared to plastic flares. Make sure your factory mounting points are in good condition—rust or damage can compromise the hold. If your JL has aftermarket bumpers or body modifications, test-fit the flare before final assembly.
The two-stage powder coat finish is durable, but avoid using abrasive tools or harsh chemicals during installation. If you need to adjust the flare's position, use a rubber mallet or a block of wood to avoid chipping the coating.
Body Armor 4x4 Rear Fender Flare Specs
-
2018-2026 JEEP WRANGLER JL REAR FENDER FLARES: 3/16" steel plate construction Steel provides strength and resistance to trail damage compared to plastic or fiberglass flares.
2018-2026 JEEP WRANGLER JL REAR FENDER FLARES
-
2018-2026 JEEP WRANGLER JL REAR FENDER FLARES: High clearance flat design The flat profile increases tire clearance, allowing for larger tires and improved off-road articulation.
-
2018-2026 JEEP WRANGLER JL REAR FENDER FLARES: Provides 5-3/4" of coverage This coverage helps keep mud and water from being thrown onto the body and rear window.
-
2018-2026 JEEP WRANGLER JL REAR FENDER FLARES: Two-stage powder coat light texture finish in black The finish is UV-resistant and requires no additional painting—install and go.
Trade-Offs to Consider
Steel flares are heavier than plastic, which can affect fuel economy and add stress to mounting points over time. The high-clearance flat design also means less coverage than some factory flares—if you drive in very muddy conditions, you may notice more spray on the body. That said, the 5-3/4" coverage is a good balance for most off-road use.
The two-stage powder coat is durable, but like any coating, it can chip if struck by rocks. Touch-up paint designed for powder-coated surfaces can handle minor blemishes. Overall, these flares are a solid upgrade for JL owners who want a rugged look with real clearance gains.
