What This Cable Does

The NANLITE PavoSlim DC Connection Cable 7.5M (model CB-PS-7.5M) is a 10-pin extension cable designed specifically for NANLITE PavoSlim 60W and 120W LED light fixtures. Its 7.5-meter (24.6 feet) length gives you more freedom to position light panels on overhead rigs, large sets, or distant control stations without being limited by the standard cable that comes with the fixture.

This cable is part of a camera, monitor, and accessory power workflow, but its primary role is extending the reach between your PavoSlim fixture and its controller. Before you order, confirming exact model compatibility is essential.

Compatibility Evidence

  • NANLITE PavoSlim DC Connection Cable 7.5M: The NANLITE PavoSlim DC Connection Cable 7.5M is a 10-pin extension cable for PavoSlim 60W & 120W LED light fixtures. This cable is not a generic power cable. It uses a specific 10-pin connector and is engineered for the PavoSlim series. Using it with other fixtures is not supported by the supplied information.

    NANLITE PavoSlim DC Connection Cable 7.5M

    NANLITE PavoSlim DC Connection Cable 7.5M

  • NANLITE PavoSlim DC Connection Cable 7.5M: The cable features a twist-lock mechanism for a secure, vibration-resistant connection. The twist-lock prevents accidental disconnections during shoots, which is important for reliability on set. Ensure your fixture has the matching 10-pin locking receptacle.

How to Verify Fit Before Ordering

Before purchasing, check that your PavoSlim fixture is a 60W or 120W model. The supplied information confirms compatibility only with those two fixtures. If you own a different PavoSlim variant or a fixture from another brand, this cable is unlikely to work.

Also confirm the connector type on both ends. The 10-pin connector is specific to NANLITE's PavoSlim line. If your fixture uses a different connector (such as a D-Tap or XLR), you will need a different cable. The manufacturer SKU CB-PS-7.5M is the exact identifier for this configuration.

Setup Steps

Follow these steps to integrate the cable into your PavoSlim lighting setup.

  1. 1. Power off the fixture: Ensure the PavoSlim light is turned off and disconnected from mains power before handling any cables.
  2. 2. Connect the cable to the fixture: Align the 10-pin connector with the receptacle on the PavoSlim fixture. Push in gently and twist the locking ring clockwise until it clicks into place. Confirm the connection is secure.
  3. 3. Connect the other end to the controller: Route the cable to your controller or power source. Connect the opposite 10-pin end using the same twist-lock method. Avoid sharp bends or pinching the cable.
  4. 4. Secure the cable run: Use cable ties or clips to fasten the cable along stands or rigging. This prevents tripping hazards and reduces strain on the connectors.
  5. 5. Power on and test: Turn on the fixture and controller. Verify that the light operates normally and that the cable does not cause flickering or intermittent connection. If issues occur, recheck the twist-lock engagement.

Build and Durability Notes

The cable is constructed with a silicone outer layer and a high-performance inner core. Silicone offers heat resistance, corrosion resistance, and long-term stability, which is beneficial in studio environments where cables are frequently coiled, moved, or exposed to heat from lights.

The twist-lock mechanism is designed to stay secure even with vibration or accidental tugs. Still, avoid yanking the cable by the cord; always disconnect by gripping the connector body.

What the Supplied Information Does Not Cover

The provided details do not specify voltage or current ratings for the cable. If you need to know the maximum power handling for your specific PavoSlim model, consult the fixture's manual or NANLITE's official specifications. The cable is intended for PavoSlim 60W and 120W fixtures; using it with higher-wattage fixtures is not confirmed by the supplied data.

Also, no instructions are given for cleaning or storing the cable. For long-term care, keep it in a dry, cool place and avoid exposure to solvents or excessive moisture.