What the PLM Carbon Fiber Intake Covers

The PLM Carbon Fiber Intake is designed specifically for the 2013–2021 Subaru BRZ, Scion FR-S, and Toyota 86/GT86 (FT86 chassis). It uses dry carbon technology and a patent-pending design to deliver a high-volume cold air path. The kit includes a carbon fiber cold air box and intake arm, with 100% CNC machined sensor connections for a precise fit.

No tune is required – it's a true bolt-on upgrade. The intake replaces the restrictive factory airbox and tubing, allowing the engine to draw cooler, denser air. This is a straightforward install for anyone comfortable with basic hand tools.

Installation Steps

These steps assume the vehicle is on level ground, the engine is cool, and you have disconnected the negative battery terminal. Always refer to the specific instructions included with your kit.

  1. Remove the factory intake: Unbolt the stock airbox from the fender and engine bay. Disconnect the mass air flow (MAF) sensor connector and remove the intake tube from the throttle body. Set the factory parts aside.
  2. Install the carbon fiber cold air box: Position the PLM carbon fiber box in the same location as the factory airbox. It uses existing mounting points – no drilling or modification required. Ensure the box sits flush and the seal around the fender opening is complete.
  3. Attach the intake arm: Slide the carbon fiber intake arm onto the throttle body opening. Tighten the included clamp evenly. The arm should be oriented so that it connects cleanly to the cold air box without kinking or rubbing against other components.
  4. Connect the MAF sensor: The PLM intake includes CNC-machined sensor ports. Install the MAF sensor into the designated bung on the intake arm. Secure it with the factory screws and reconnect the electrical connector. Verify the sensor is seated correctly – a loose MAF can cause idle issues.
  5. Secure all clamps and check for clearance: Tighten all hose clamps and verify that the intake does not contact the hood, fan shroud, or other moving parts. Reinstall any factory brackets or covers that were removed. Double-check that the intake is fully seated and all connections are snug.
  6. Reconnect the battery and test: Reconnect the negative battery terminal. Start the engine and let it idle for a minute. Check for any unusual noises or loose fittings. If the engine runs smoothly, take a short test drive to confirm proper operation.

What the Catalog Confirms

  • PLM Carbon Fiber Intake - 2013+ Subaru BRZ FR-S 86 FT86: No tune is required, bolt-on installation. You can install this intake without ECU reflashing or aftermarket tuning software. It's a direct replacement that works with the factory engine management.

    PLM Carbon Fiber Intake - 2013+ Subaru BRZ FR-S 86 FT86

    PLM Carbon Fiber Intake - 2013+ Subaru BRZ FR-S 86 FT86

  • PLM Carbon Fiber Intake - 2013+ Subaru BRZ FR-S 86 FT86: High Volume Cold Air Intake with Dry Carbon Technology. Dry carbon is lighter and more heat-resistant than wet-lay carbon. The high-volume design reduces intake restriction, which can improve throttle response.

  • PLM Carbon Fiber Intake - 2013+ Subaru BRZ FR-S 86 FT86: 100% CNC machined sensor connections. Precision-machined ports ensure the MAF sensor fits correctly and reads accurately. This helps avoid check-engine lights and rough idle after installation.

Fitment Checkpoints Before You Buy

This intake fits the 2013–2021 Subaru BRZ, Scion FR-S, and Toyota 86/GT86. It does not fit other Subaru or Toyota models. The kit is built in the USA and uses a patent-pending design. No tune is required, but if you have other modifications (aftermarket headers, turbo, or supercharger), verify that the intake will clear those components.

The catalog does not mention specific horsepower gains, dyno charts, or sound clips. If those details matter to your decision, check with the manufacturer or independent forums. The intake is sold in a liquidation sale – final sale price $795 (regularly $1,295, retail $1,595). Stock is limited.