The boot is a base cover, not a full-body case
If you are deciding whether to keep the OG+ Silicone Boot on your Chiller all day, start with what the product actually is. The catalog describes it as a silicone boot that fits on your OG+ and Legacy Chillers. That makes it a bottom-of-the-bottle accessory, not a sleeve that wraps the whole Chiller.
That distinction matters for chiller base protection. The boot sits where the Chiller meets tables, counters, car cup holders and bag bottoms. It does not cover the upper body, lid or handle area. So when you ask whether to leave it on, you are really asking whether you want a removable silicone layer between your Chiller base and the surfaces it touches.
What the catalog confirms about the OG+ Silicone Boot
-
OG+ Silicone Boot: These silicone boots will fit on your OG+ and Legacy Chillers. This is the compatibility statement to check first. If your Chiller is not an OG+ or Legacy model, the supplied information does not confirm a fit.
OG+ Silicone Boot
-
OG+ Silicone Boot: What's Included: (1) Silicone Boot (or one of each if you order the multi-pack). A single boot covers one Chiller base. The multi-pack option is the one to choose if you want boots for more than one Chiller or want to mix colors.
-
OG+ Silicone Boot: Available colors: Black and Semi-Transparent. Color is the only listed option type. The semi-transparent version may show more of the Chiller base underneath, while black gives a solid, contrasting look.
When leaving the boot on makes sense
Leave the boot on when your Chiller spends the day moving between hard surfaces. A silicone layer at the base is the most direct way to add a buffer between the bottom of the Chiller and countertops, desk edges or cup holders. If your daily routine involves setting the Chiller down repeatedly, the boot stays useful on the base rather than in a drawer.
The boot also makes sense if you want to change the look of your Chiller without covering the body. Because it fits only on the base and comes in Black or Semi-Transparent, it is a low-commitment way to customize the bottom of an OG+ or Legacy Chiller. The catalog also notes that you can mix and match colors, which is easiest with the multi-pack.
When taking the boot off is the better call
Take the boot off when you want to inspect the base of your Chiller. The boot covers the bottom, so any check of that area is easier with the boot removed. The supplied information does not include cleaning instructions for the boot, so do not assume a dishwasher or hot-water routine. If you are unsure, hand washing is the safer default for silicone accessories, but treat that as general practice rather than a manufacturer instruction.
Remove it if the boot feels loose or if you notice grit trapped between the boot and the Chiller base. The catalog does not describe a locking mechanism or a tight-seal design, so the boot should be treated as a removable cover. A quick visual check when you take it off is more reliable than assuming the base stays clean underneath.
Day-to-day habits that keep base protection useful
- Set the Chiller down on the boot, not the bare base: The boot only helps if it is between the Chiller and the surface. If you often remove it, the base gets no silicone buffer on those days.
- Check the fit after removing and refitting: The catalog confirms fit for OG+ and Legacy Chillers but does not list a stretch rating or installation steps. Refit the boot so it sits evenly on the base, and stop using it if it no longer stays in place.
- Keep the boot dry before storing: The supplied information does not include drying or storage instructions. A dry boot is less likely to trap moisture against the Chiller base during storage.
- Use the multi-pack if you rotate Chillers: One boot is included per single order. If you use both an OG+ and a Legacy Chiller, the multi-pack is the listed way to get one of each.
What the catalog does not confirm
The supplied product record does not include care instructions, a material thickness, a slip rating or a claim that the boot prevents scratches, dents or leaks. It also does not state that the boot is dishwasher safe or heat resistant. Those are reasonable questions, but the catalog does not answer them, so avoid treating the boot as a guaranteed shield against every kind of damage.
What the catalog does support is narrower and still useful: the boot fits OG+ and Legacy Chillers, comes in Black or Semi-Transparent, and is sold as one boot or as a multi-pack with one of each color. For day-to-day chiller base protection, that is enough to decide whether you want a removable silicone layer on the bottom of your Chiller.
