Start with the Groove, Not the Color
The AS568-347 silicone O-ring is a specific size with a 4.225" inner diameter and a 0.21" cross-section. Before you consider material or color, confirm that your groove or gland matches these dimensions. The dash number 347 is the AS568 standard size identifier; if your application calls for a dash 347, this is the O-ring you need.
The catalog record shows an inner diameter of 4.225" (107.31 mm) and a cross-section of 0.21" (5.33 mm). These are imperial measurements, so if your design uses metric dimensions, convert carefully. A mismatch of even 0.01" can cause leaks or extrusion.
Catalog Reference: AS568-347 Silicone O-Ring
-
0.21" CS X 4.225" ID Silicone O-Rings | AS568-347 | Dash 347 | FDA Compliant | 70 Durometer | Red (20 / Pkg.): Inner diameter: 4.225" (107.31 mm); Cross-section: 0.21" (5.33 mm); AS568 dash size: 347. These are the critical fit dimensions. Verify them against your groove before purchasing.
0.21" CS X 4.225" ID Silicone O-Rings | AS568-347 | Dash 347 | FDA Compliant | 70 Durometer | Red (20 / Pkg.)
-
0.21" CS X 4.225" ID Silicone O-Rings | AS568-347 | Dash 347 | FDA Compliant | 70 Durometer | Red (20 / Pkg.): Material: Silicone (also known as VMQ, Silastic); Durometer: 70 Shore A; Color: Red. 70 durometer is a medium-hardness silicone that seals well in moderate-pressure applications. Red color is standard for silicone but does not indicate any special property.
-
0.21" CS X 4.225" ID Silicone O-Rings | AS568-347 | Dash 347 | FDA Compliant | 70 Durometer | Red (20 / Pkg.): Temperature range: -80°F to +450°F (-62°C to +232°C). This O-ring can handle extreme cold and high heat, making it suitable for ovens, autoclaves, and cryogenic service.
-
0.21" CS X 4.225" ID Silicone O-Rings | AS568-347 | Dash 347 | FDA Compliant | 70 Durometer | Red (20 / Pkg.): Compliance: FDA 21 CFR 177.2600. This means the material is acceptable for repeated food contact under FDA regulations. It is not a blanket approval for all food types or conditions; verify your specific use case.
FDA 21 CFR 177.2600: What It Covers and What It Does Not
The AS568-347 silicone O-ring is listed as compliant with FDA 21 CFR 177.2600, which covers rubber articles intended for repeated food-contact use. This regulation specifies acceptable extractive limits and use conditions for silicone elastomers.
However, the regulation does not cover every food type or processing condition. For example, high-fat or high-alcohol foods may have different extractive limits. The catalog does not provide specific use restrictions beyond the temperature range. If your application involves acidic, fatty, or alcoholic foods, you should consult the manufacturer or conduct your own migration testing.
Also, FDA 177.2600 does not address wear life, sterilization cycles, or compatibility with cleaning chemicals. These factors depend on your specific process and should be validated separately.
70 Durometer Red Silicone: Hardness and Color in Context
70 Shore A is a common durometer for O-rings. It offers a balance between sealing force and compression set resistance. Softer O-rings (50-60 durometer) seal better on rough surfaces but may extrude under pressure; harder ones (80-90 durometer) resist extrusion but may not conform as well.
The red color is typical for silicone O-rings but carries no functional meaning. Do not rely on color alone to identify material; always check the specification or certification. The catalog confirms the material is silicone (VMQ) and the durometer is 70 Shore A.
Temperature Range: Compare It to Your Whole Process
The silicone O-ring is rated from -80°F to +450°F (-62°C to +232°C). This covers most food-processing temperatures, including steam cleaning and hot-fill operations. However, the temperature rating applies to the material itself, not to the seal under pressure or in dynamic applications.
If your process cycles rapidly between hot and cold, thermal expansion may affect the seal. The catalog does not provide thermal cycling data. For static seals at constant temperature within the range, this silicone O-ring is a reliable choice.
Pre-Purchase Checklist for Food-Contact Sealing
Before you order the AS568-347 silicone O-ring, run through these checks:
- Groove dimensions: Confirm that your gland groove matches 4.225" ID and 0.21" cross-section. A slight mismatch can cause leakage or extrusion.
- Temperature exposure: Ensure your process stays within -80°F to +450°F. If you exceed 450°F, even briefly, silicone may degrade.
- Food contact type: FDA 177.2600 covers repeated contact. If you have a single-use or high-fat application, verify with the manufacturer.
- Chemical compatibility: Silicone resists many foods but can swell in oils or solvents. The catalog does not list chemical resistance; test in your actual media.
- Durometer suitability: 70 Shore A works for most static seals. If your application has high pressure or dynamic movement, consider a different durometer.
When the AS568-347 Silicone O-Ring Is the Right Call
This O-ring is a strong choice when you need a food-contact-compliant seal in a standard dash 347 size, with a wide temperature range and medium hardness. It is particularly useful in food processing equipment, hot water systems, and steam lines where FDA compliance is required.
If your application requires higher chemical resistance (e.g., fuels, strong acids), you might consider a different elastomer like FKM or EPDM. The catalog does not provide comparative data, so base your decision on your own media compatibility testing.
The pack quantity is 20 O-rings per package. Plan your order accordingly. The catalog price is USD 36.39 (compared to USD 54.32).
