Quick answer

To set up your Soltron L-65 Turbo Power VHP tanning bed, first download the official Soltron L-65 manual, then follow its wiring and configuration steps exactly. The manual is essential for safe installation and correct VHP lamp operation. If you don't have it, purchase the PDF manual from Sun Tanning Store and keep it on hand during setup.

Why the Soltron L-65 manual is non-negotiable for VHP setup

The Soltron L-65 Turbo Power VHP is a high-output tanning bed, and VHP (Very High Performance) systems demand precise electrical and ventilation setup. Without the manufacturer's manual, you risk incorrect voltage settings, improper lamp seating, or inadequate cooling—all of which can shorten equipment life or create safety hazards. The manual provides exact wiring diagrams, clearances, and step-by-step configuration for the Turbo Power ballast system. Because the Soltron L-65 is a specific model, generic tanning bed instructions won't cover its unique control panel or VHP lamp array. Always use the model-specific Soltron L-65 manual.

What you'll need before you start

Gather the following: the Soltron L-65 Turbo Power VHP tanning bed, the correct Soltron L-65 manual (digital PDF is fine), a dedicated 220V circuit (check manual for exact amperage), proper ventilation space, and basic tools like a screwdriver and voltage tester. If you're replacing acrylics, consider upgrading to premium rigid acrylic for better UV transmission—but only after the bed is fully assembled and tested. Have a helper for lifting the canopy, as these beds are heavy and awkward to maneuver alone.

Step-by-step Soltron L-65 Turbo Power VHP setup

Follow these steps in order. Skipping or reordering can lead to electrical faults or damaged components. The manual's sequence is designed to protect both you and the bed.

Soltron L-65 setup steps: actions and checkpoints

  1. Download and review the manual: Purchase and download the Soltron L-65 Turbo Power VHP 12 Tanning Bed Manual PDF. Read the entire manual before touching the bed—especially the electrical and safety sections. Checkpoint: Confirm the manual matches your exact model (L-65 Turbo Power VHP). If unsure, contact support before ordering.
  2. Position and level the bed: Place the bed on a flat, level surface with the clearances specified in the manual. Ensure adequate ventilation around the ballast and lamps. Use a level to avoid frame stress. Common mistake: Ignoring clearance requirements—VHP beds generate significant heat and need proper airflow.
  3. Wire the electrical connection: Following the manual's wiring diagram, connect the bed to a dedicated circuit of the correct voltage and amperage. Use a voltage tester to verify power is off before wiring. Checkpoint: Double-check all connections against the diagram. If uncertain, hire a licensed electrician.
  4. Install VHP lamps and acrylics: Insert the VHP lamps firmly into sockets, ensuring they are fully seated. If replacing acrylics, handle them carefully and remove protective film. Do not overtighten retainers. Common mistake: Forcing lamps can crack sockets. If a lamp doesn't seat easily, check pin alignment.
  5. Configure controls and test: Power on the bed and follow the manual to set timers, session limits, and any Turbo Power settings. Run a short test cycle to confirm lamps ignite and fans operate. Checkpoint: If lamps flicker or fans don't run, stop and consult the troubleshooting section of your manual.
  6. Perform a safety check: Verify that all panels are secure, no wires are pinched, and emergency shut-off works. Clean acrylics with a non-ammonia cleaner before first use. Next step: Log your setup date and keep the manual accessible for future maintenance.

Manual and acrylic options from Sun Tanning Store

  • Soltron L-65 Turbo Power VHP 12 Tanning Bed Manual: Ordering this product will allow you to download a PDF file containing an Soltron L-65 Turbo Power VHP 12 Tanning Bed Manual. This is a digital product and the PDF is not eligible for return, exchange or refund once you submit the order. Instant access to the exact manual you need for safe setup, but double-check your model number before buying since digital sales are final.
  • Tan America VIP Tanning Bed Replacement Acrylic (Top Canopy): Remodel your Tan America VIP Tanning Bed to improve UV light transmission by installing brand new canopy acrylic! This is premium grade rigid replacement acrylic that is shipped flat and not rolled up in a box like other lower grade acrylic replacements. If you're restoring a compatible bed, flat-shipped rigid acrylic avoids the waviness and fit issues common with rolled acrylic, ensuring consistent tanning performance.