Start with the three expressions you actually have

The Yukihana Lamy Nendoroid ships with three interchangeable face plates: a gentle smiling face, a mischievous grinning face, and an intense pressuring face. That is the whole expression set confirmed by the product record, so plan your display around those three moods rather than expecting extra faces.

Because the figure is only 3.94 inches (10.01 cm) tall, each face plate is small and easy to misplace. Set up a shallow tray or a clean cloth before you begin swapping, and work over a table rather than carpet so a dropped plate stays findable.

What the Lamy Nendoroid record confirms

A safe order for changing Lamy's face plate

The supplied product information does not include a manufacturer step-by-step for plate removal, so treat the sequence below as a careful handling routine rather than an official instruction. If the plate resists, stop and check the fit instead of forcing it.

  1. Clear and contain the workspace: Work on a clean, uncluttered surface with the tray or cloth ready. At 3.94 inches tall, the figure and its parts are small enough to roll or bounce out of reach.
  2. Remove accessories first: Take off any held or attached accessory parts before touching the face area, so nothing snags or drops while your attention is on the plate.
  3. Support the head while separating the plate: Hold the head steady with one hand and ease the current face plate out with the other. Keep the motion straight rather than twisting.
  4. Seat the new plate fully before posing: Press the chosen expression into place until it sits flush, then reattach accessories. A partly seated plate can shift when you adjust the head.
  5. Return unused plates to storage immediately: Put the two plates you are not using back in a labelled bag or compartment before you start adjusting the pose, so they do not get lost mid-setup.

Matching each face to a display mood

You do not need a different pose for every plate, but pairing expression with accessory choice makes the swap feel intentional.

  • Gentle smiling face: The calmest of the three expressions. Use it for a front-facing shelf spot where Lamy is meant to look welcoming rather than mid-stream.
  • Mischievous grinning face: Pairs naturally with a more active arrangement of the supplied accessories and parts, since the expression reads as playful.
  • Intense pressuring face: The strongest expression in the set. Give it the most visible angle on the shelf so the face is not hidden behind other figures.

Keep the accessories together, not just the figure

The record confirms a range of accessories and parts but does not list them individually, so the practical move is to inventory what arrives in the box on day one. Photograph the parts laid out next to the figure, then store the small pieces in a divided box.

When you rotate Lamy's expression, rotate the accessory setup with it. A single stored kit means you are never hunting for a part while the figure sits half-dressed on the shelf.

Display and dust routine for a small Hololive figure

The supplied record does not specify materials, cleaning products, or a joint-tightening procedure, so keep the routine conservative and avoid anything that could attack paint or plastic.

  • Dust little and often: A soft brush or dry cloth used gently is safer than a wet wipe, since no cleaning agents are confirmed for this figure.
  • Keep the shelf stable: Place Lamy where the shelf is not knocked regularly. At 3.94 inches tall she is easy to topple if something brushes past.
  • Watch the sunlight: Display away from direct sun. The record does not confirm UV resistance, so limiting exposure is the cautious choice.
  • Handle joints only when needed: The record does not confirm a joint-tightening method. If a joint feels loose, avoid repeated forceful re-posing and check the fit rather than applying unlisted products.

What the listing does not tell you

The supplied record gives height and packaging dimensions (7 inches by 3.50 inches by 5.50 inches) but does not confirm an age rating, materials, a stand type, or a specific plate-removal method. Treat those as open questions rather than assumed features.

The record also does not list the individual accessories, so the box contents are the reliable source. Check what is included when the figure arrives, and keep the packaging dimensions in mind if you need a display case or shelf slot that fits the box.