Quick answer

Display Wuthering Waves figures on a stable, closed or semi-enclosed shelf out of direct sun, with each figure's base fully supported and at least a few centimeters of clearance from the shelf edge. Dust with a soft brush or blower weekly, keep lighting indirect and low-heat, and re-check stability whenever you move or add a piece.

Before you place anything: audit the spot

Pick a location that stays out of direct sunlight and away from heat sources like radiators, vents, or strong lamps. UV exposure and heat are the two quiet causes of fading, warping, and paint damage on PVC and ABS figures, and neither is obvious until it's too late.

Check the shelf itself: is it level, rated for the weight, and deep enough that a figure's base sits fully on the surface with room behind it? A 1/7 scale figure can be top-heavy, so a shelf that flexes or wobbles under load is a real risk. If you're using a glass cabinet, confirm the shelf pins are seated and the cabinet is on a flat floor.

Match the display method to the figure's size

Scale figures need vertical clearance, not just footprint space. A figure listed at roughly H267mm or H285mm will need a shelf gap taller than that once you account for a base, a raised arm, or a weapon. Measure the tallest point, not the box height, and leave a few centimeters above it.

Smaller plush and accessory items can share a shelf, but keep them from pressing against painted surfaces. Plush fibers and metal buckles can scuff or transfer dye onto a figure over time, so give plush its own zone or a clear gap.

Dust protection that doesn't trap moisture

A closed cabinet with a door is the simplest dust protection, but it needs some airflow. If the cabinet is fully sealed and the room is humid, condensation can form on cool surfaces. A cabinet with a small gap or a breathable back panel is usually a better balance than a completely airtight box.

If you display in the open, dust more often and use a soft brush or a bulb blower rather than a cloth. Rubbing dust across a painted surface is how micro-scratches and dull spots appear, especially on matte finishes.

Lighting without heat or glare

LED strips and puck lights run cool and are the safest choice for anime figure lighting. Avoid halogen or incandescent bulbs near figures; they generate heat and can soften or warp PVC over long sessions.

Aim lights from above and slightly in front rather than straight at the face. This reduces glare on glossy paint and keeps the figure's silhouette readable. If you use colored LEDs, keep them on a timer so the figure isn't under strong colored light all day.

Stability, posing, and the base

Seat the figure fully onto its base pegs and check that it doesn't rock. If a figure leans, don't force it; a small piece of museum putty under the base can add grip without damaging the surface. Keep figures away from shelf edges and doors that swing past them.

For figures with thin supports or dynamic poses, avoid placing them where they can be bumped by a vacuum, a pet, or a door. The most common break isn't a fall from height; it's a tip-over from a light knock.

A maintenance rhythm that actually holds up

Dust weekly with a soft brush or blower, and do a deeper check monthly: look for leaning, loose bases, dust buildup in crevices, and any change in paint or finish. Rotate figures that sit in the same spot for months so no single piece takes all the light exposure.

When you rearrange, move one figure at a time and support the base, not the hair or an accessory. Keep the original box and blister for anything you might store later; they're the safest transport option you already own.

Display setup steps

  1. Measure the tallest point and shelf gap: Use the figure's listed height as a starting point, then add clearance for the base and any raised parts. For a roughly 267mm or 285mm scale figure, a shelf gap only slightly taller than the figure will feel cramped and risky. Checkpoint: if the figure's head or weapon is within a finger's width of the shelf above, move it.
  2. Choose a stable, low-traffic surface: A level cabinet shelf or a wall-anchored bookcase beats a freestanding narrow shelf. Avoid spots where doors, pets, or vacuum cords pass close by. Checkpoint: push the shelf gently; if it wobbles, fix that before placing anything.
  3. Seat the base and test for rocking: Press the figure fully onto its pegs, then nudge the base lightly. If it rocks or leans, add a small amount of museum putty under the base rather than bending the figure. Common mistake: forcing a misaligned peg can crack the base or stress the ankle joint.
  4. Add dust protection appropriate to the room: Use a cabinet with a door for the best figure dust protection, or dust more frequently if you display in the open. Avoid airtight enclosures in humid rooms. Checkpoint: if you see condensation on the inside of glass, improve airflow.
  5. Set lighting above and in front: Use cool LED lighting and angle it down and slightly forward. Keep colored or strong lights on a timer so figures aren't under constant exposure. Common mistake: halogen or hot bulbs close to PVC can cause slow warping.
  6. Build a weekly and monthly care habit: Dust weekly with a soft brush or blower, and monthly check for leaning, loose bases, and finish changes. Rotate positions so no figure takes all the light. Next step: note the date you set up each figure so you can spot slow changes.

Product facts that affect display planning

  • [Pre-order] Wuthering Waves - Jinhsi 1/7 Scale Figure APEX: Wuthering Waves Jinhsi 1/7 scale figure by APEX, approx. H267mm, PVC and ABS, with a shikishi board bonus. At roughly 267mm tall, plan a shelf gap taller than the figure and leave room for the bonus board so it doesn't press against the figure.
  • [Pre-order] Wuthering Waves - Augusta 1/7 Scale Figure Hobbysakura: Wuthering Waves Augusta 1/7 scale figure by Hobbysakura, approx. H285mm, PVC and ABS, with a 58mm badge bonus. The taller of the two at about 285mm, so measure your tallest shelf clearance before committing to a spot; the badge is small enough to store separately.
  • [Pre-order] Wuthering Waves - Tidal Letters Series Plush Phone Stand FUN4YEAH: Wuthering Waves Tidal Letters Series Plush Phone Stand by FUN4YEAH, characters Lynae, Mornye, Denia, and Luuk Herssen, with buckle and plush dimensions around 74-92mm. These small plush pieces fit on a lower shelf or desk edge, but keep them from pressing against scale figures to avoid dye transfer or scuffs.