Quick answer

Installing a Lascal BuggyBoard is straightforward: attach the connector arms to your stroller frame, secure them with the cotter pins, then click the board onto the arms. The key is choosing the correct mounting hole and tightening the cotter pin before every ride.

What You Need Before You Start

Before installing, check that your stroller frame has a horizontal or slightly angled bar between the rear wheels. The Lascal BuggyBoard connector arms wrap around this bar. If your stroller has a very thick frame or unusual shape, the Fred Safety Universal Stairpost Fitting Kit can provide a flat mounting surface, though it's designed for stair gates and may require extra creativity to adapt.

Also confirm your BuggyBoard model: the Lascal Mini fits most single strollers and is suitable for toddlers aged 2–5, while the Maxi works with wider frames. Both use the same connector system, so the installation steps are identical.

Common Mistakes to Avoid

The most frequent error is choosing the wrong mounting hole on the connector arm. The arm has three holes; use the one that positions the board closest to the stroller without rubbing the wheels. If the board is too far back, it can tip when your child steps on.

Another mistake is forgetting to tighten the cotter pin before each use. The Lascal BuggyBoard Spare - Cotter Pin Grey is a plastic threaded pin that can loosen over time. A quick hand-tighten before every outing prevents the board from detaching.

Step-by-Step Installation Guide

  1. Attach the connector arms to the stroller frame: Open the connector arms and place them around the rear horizontal bar of your stroller. Ensure the arms are centered and level. Close the arms until they click shut. The rubber pads should grip the frame firmly without slipping. Checkpoint: The arms should not slide along the frame when you push them. If they move, adjust the tension or reposition on a different section of the bar.
  2. Select the correct mounting hole: Each connector arm has three holes. Choose the hole that brings the BuggyBoard as close to the stroller as possible without touching the wheels when the board is attached. Insert the cotter pin through the chosen hole and the arm's bracket. Common mistake: Using the wrong hole can cause the board to wobble or hit the stroller wheels. Test by temporarily placing the board on the arms before tightening.
  3. Secure the cotter pin: Hand-tighten the plastic cotter pin until it is snug. Do not overtighten, as the plastic can strip. The pin should hold the arm firmly in place. Repeat for both sides. Checkpoint: The cotter pin must be tightened before every use. A loose pin is the most common cause of BuggyBoard detachment.
  4. Attach the BuggyBoard platform: Align the slots on the underside of the BuggyBoard with the connector arm brackets. Press down firmly until you hear a click. Give the board a gentle tug to confirm it is locked in place. If the board does not click, the arms may be misaligned. Remove the board, adjust the arm position, and try again.
  5. Test the installation before use: Push the stroller a few steps with your child standing on the board. Check that the board does not hit the ground or the stroller wheels. Listen for any rattling sounds, which indicate loose parts. Verdict: If the board is stable and your child can ride comfortably, the installation is complete. If not, revisit step 2 and choose a different hole.

Products That Help With Installation

  • Lascal BuggyBoard® Spare - Cotter Pin Grey: A replacement BuggyBoard Cotter Pin for your Lascal BuggyBoard. A plastic threaded pin approximately 2 inches long which fits through the Lascal BuggyBoard Connector, attaching your board to the pram. Part number 81520 Compatible with Lascal Mini & Maxi BuggyBoard. Attaches to 1 of the 3 holes in the Left & Right Arm, depending on pram. Tip: the Cotter Pin will need to be tightened before every use. Having a spare cotter pin on hand ensures you can quickly replace a lost or worn pin, keeping the board securely attached. The need to tighten it before every ride is a simple habit that prevents accidents.
  • Fred Safety Universal Stairpost Fitting Kit - Pure White: Compatible with any safety gate, the Fred Universal Stairpost Fitting Kit is a flexible, no-screw solution for installing a stair gate. Provides a secure flat surface for your gate to be fitted to, it’s the perfect universal kit. Suitable for all stair posts, these can fit against the trickiest of stair posts, newel posts and balusters of all sorts of shapes and sizes. Uniquely designed offering damage free installation. If your stroller frame is unusually shaped or has a round, tapered bar, this kit can create a flat surface for the BuggyBoard arms to grip. It's not a dedicated stroller product, so test fitment carefully before relying on it.