Quick answer
To set up a Fleshlight Shower Mount, clean and dry a smooth tile or glass wall, press the suction base firmly, lock the adjustable arm, then attach your Fleshlight case and test the angle before use. The most common failure is mounting on textured or soapy surfaces, so always check the seal and rinse the mount after every session.
Choose a wall that can hold the seal
The Fleshlight Shower Mount relies on suction, so the surface matters more than how hard you press. Smooth, non-porous tile, glass, or polished acrylic gives the best hold. Grout lines, textured stone, and matte plastic break the seal and cause sudden release. Clean the area with a degreaser or soap, rinse thoroughly, and dry it completely before mounting. Even a thin film of soap or conditioner can make the mount slide. If your shower only has textured walls, use a smooth glass panel or a large tile square instead.
Attach and position your Fleshlight case
The mount is designed to hold your favorite Fleshlight product in the shower. Screw or click the case into the mount according to the mount's instructions, then tighten the adjustable arm so the case stays at your preferred angle. Point the opening slightly downward to let water drain rather than pool inside. Do not overtighten the arm; it should hold position without cracking the case. If you use a Fleshjack Boy sleeve, check that its case diameter fits the mount before you start.
Test the hold before you commit
After mounting, press firmly on the suction base for 10–15 seconds, then give the arm a gentle tug. If it shifts, remove it, dry the wall again, and reattach. A small spray of water on the suction cup can improve the seal, but too much water makes it slide. Once the mount feels solid, adjust the angle with one hand while the other supports the case. Keep a towel nearby in case the seal releases unexpectedly.
Clean and store the mount after every use
Shower steam and body oils degrade suction over time. Rinse the mount with warm water, wipe it with a mild toy cleaner or soap, and dry it fully before storage. Do not leave it attached to the wall between sessions; continuous pressure can warp the suction cup. Store it loose in a dry place away from direct sunlight. If the suction cup loses tackiness, wash it with warm soapy water and let it air dry completely.
Step-by-step shower mount setup
- Clean and dry the wall: Use a mild cleaner to remove soap residue, then dry the surface completely with a clean towel. Checkpoint: the wall should feel squeaky-clean and dry before you attach the mount.
- Press and lock the suction base: Press the suction cup firmly against the wall for 10–15 seconds, then flip the locking tab if your mount has one. Mistake to avoid: pressing on a wet or soapy wall, which prevents a strong seal.
- Attach your Fleshlight case: Screw or click the case into the mount, then adjust the arm to your preferred angle and tighten it gently. Checkpoint: the case should sit securely without wobbling when you touch it.
- Test the hold with a gentle tug: Pull lightly on the arm to confirm the suction is holding. If it shifts, re-clean and dry the wall, then reattach. Mistake to avoid: skipping the tug test and discovering a weak seal mid-session.
- Rinse and dry after use: Remove the mount, rinse it with warm water, wipe it with toy cleaner, and let it air dry completely before storage. Next step: store the mount loose in a dry place, not attached to the shower wall.
Product facts
- Fleshlight Shower Mount: The Fleshlight Shower Mount is a suction-based, adjustable attachment that adheres your Fleshlight product securely to the shower wall for hands-free sessions. This is the core accessory for hands-free shower use, and its adjustable arm lets you set a comfortable angle before you start.
- Classic Pink Butt™ Wonder Wave: The Classic Pink Butt Wonder Wave combines the Wonder Wave texture with an anal entrance for a snug, wavy sensation. If you prefer anal-style stimulation, this sleeve is a compatible option to pair with the shower mount for hands-free play.
- Max Konnor: Max Konnor is a Fleshjack Boy sleeve with a texture option, molded from the performer. Fleshjack Boy sleeves fit standard Fleshlight cases, so you can use this sleeve with the shower mount if you want a performer-based experience.
