Quick answer
Place the Ingenuity Easy Rinse Baby Bather on a stable, flat surface inside a clean adult tub or a large sink, fill the tub with warm water only up to your baby's chest, and never leave your baby unattended. The one-piece seat cradles your newborn with a non-slip layer, and the perforated design lets water drain through instead of pooling. Always keep one hand on your baby, and clean the bather after every use.
Prepare the bath area before you pick up your baby
Gather everything you need within arm's reach: a soft washcloth, mild baby wash, a hooded towel, and a clean diaper. Place the Easy Rinse Bather directly on the floor of a clean adult tub or a large, stable sink. Check that the surface under the bather is flat and free of soap residue, because a slippery tub floor is the most common cause of a bather sliding mid-bath. Fill the tub with warm water to about 90°F (32°C) and test it with your wrist or elbow. The bather's perforated design lets water flow through, so the water level in the tub matters more than the level inside the seat. As a checkpoint, if the bather shifts when you press down on it with one hand, drain the tub and reposition it before bringing your baby in.
Lower your baby in feet first and keep a hand on them
Undress your baby and lower them into the bather feet first, supporting the head and neck with one hand until their bottom is settled in the seat. The non-slip layer helps hold them in place, but it is not a substitute for your hand. Keep one hand on your baby at all times, even when they seem calm. Wash the face and head first with plain warm water, then use a small amount of mild baby wash on the body. Rinse by scooping water over your baby or using a cup, letting the water drain through the perforations. A common mistake is filling the bather like a bucket; water should pass through, not pool around your baby. Checkpoint: if your baby's chest is submerged or the water feels hot, stop and adjust before continuing.
Lift your baby out before draining the tub
Have a hooded towel open and ready before you lift your baby. Reach under both arms and support the head and neck as you lift them out, then wrap them immediately. Never drain the tub while your baby is still in the bather, because moving water can shift the seat and lower the water temperature quickly. After your baby is dry and dressed, empty the tub and rinse the bather with warm water. A common mistake is leaving the bather sitting in standing water between baths, which can leave a slippery film. Checkpoint: if the bather still feels soapy after rinsing, wash it with mild soap and warm water, then rinse again and air dry.
Clean the bather after every bath and store it dry
Wipe the bather with a clean, damp cloth or rinse it under warm running water after each use. For a deeper clean, use mild soap and a soft sponge, then rinse thoroughly. Avoid abrasive cleaners, bleach, or scrubbing pads, which can damage the non-slip layer. Stand the bather on its side or place it in a drying rack so air can reach the underside, and store it out of direct sunlight once dry. If you notice cracks, tears, or a non-slip layer that has become smooth or peeling, replace the bather rather than continuing to use it. Checkpoint: run your fingers over the non-slip surface monthly; if it no longer feels grippy, it is time for a new one.
Know when to move up to a larger tub
The Easy Rinse Bather is designed for the newborn and infant stage, when your baby needs head and neck support and stays relatively still. Once your baby can sit upright with steady head control and starts splashing or trying to climb out, a larger tub gives them more room and keeps water safely contained. The Summer by Ingenuity Comfy Clean Deluxe Newborn to Toddler Tub grows with your baby from infant to toddler with a soft fabric sling and foam pads, so it can replace the bather when your baby outgrows the one-piece seat. Checkpoint: if your baby's feet or head press against the edges of the bather, or if they can push themselves up, it is time to size up.
Bath-time steps at a glance
- Set up on a flat, stable surface: Place the bather on the floor of a clean adult tub or a large sink. Press down with one hand to check it does not slide. If it shifts, drain and reposition before bringing your baby in.
- Fill with warm water to chest level: Target about 90°F (32°C) and test with your wrist. The perforated design lets water pass through, so tub level matters more than seat level. Never fill the bather itself like a bucket.
- Lower baby in feet first, hand on them always: Support the head and neck until they settle into the seat. Wash the face first with plain water, then use mild baby wash. One hand stays on your baby for the whole bath.
- Lift out before draining: Wrap your baby in a hooded towel first, then empty the tub. Never drain water while your baby is still in the bather. Moving water can shift the seat and drop the temperature fast.
- Rinse and air dry after every bath: Use mild soap and warm water, avoid abrasive cleaners, and stand the bather on its side to dry. Check the non-slip layer monthly; replace if it feels smooth or peeling.
Product facts
- Ingenuity Easy Rinse Baby Bather - Gray: One-piece infant bath seat with a non-slip layer and perforated design that lets water flow through without pooling. The non-slip layer adds stability during bath time, while the perforations mean you do not have to bail water out of the seat.
- Summer by Ingenuity Comfy Clean Deluxe Newborn to Toddler Tub: Extra-large tub with a soft fabric sling for newborns and foam pads with contoured sides and seating for older babies. A good next step when your baby outgrows the bather and needs more room to sit and splash.
